Certified in Automation Course — Pumo Technovation

Certified in Automation

Total Number of Modules8

Total Number of Topics157

Estimated Duration182:00 H

Module 1 – Introduction of Automation

Introduction of Automation – What Is Automation, Revolution of Industrial Automation, Basic Electrical & Circuit Breaker, Types of Relay & Contactor60 Mins

Module 2 – Control Panel Wiring

Relay - Circuit Design – Relay Circuit Design for Logic Gates: AND Gate, OR Gate30 Mins
Relay - Circuit Design Practice – Design Relay Circuit for NAND, NOR, Ex-OR, Ex-NOR Gates60 Mins
Relay - Basic Workout – 5 Basic NO, NC Concepts from PLC120 Mins
Control Panel - Circuit Design – Types of Panel Wiring in PLC, Designing Panel Wiring for Delta PLC (Sink Input Source Output)60 Mins
Control Panel - Circuit Design Practice – PLC Control Panel Wiring: Sink-Sink, Source-Sink, Source-Source90 Mins
Control Panel - Circuit Wiring – Delta PLC Wiring (Sink Input Source Output), Power Supply, Input & Output Module for PLC300 Mins

Module 3 – Delta PLC (WPLSoft)

Introduction – Specification of Delta PLC, Device Overview, Software Introduction & Installation30 Mins
Basic Instructions Part 1 – Input Addressing (X0), Output Addressing (Y0), NO, NC, Coil, Vertical & Horizontal Line30 Mins
Basic Instruction Part 1 – Workout: Ladder Diagram for Logic Gates & Reference Workout240 Mins
Basic Instruction Part 2 – Latching, Un-Latching, Memory Contact (M0)30 Mins
Basic Instruction Part 2 – Workout180 Mins
Basic Instruction Part 3 – Rising Edge, Falling Edge, Set, Reset30 Mins
Basic Instruction Part 3 – Workout120 Mins
Timer Instruction – Overview, Working, Types, Addressing of Timer30 Mins
Timer Instruction – Workout180 Mins
Counter Instruction – Overview, Working, Types, Addressing of Counter30 Mins
Counter Instruction – Workout120 Mins
Arithmetic Instruction – 16-Bit (ADD, SUB, DIV, MUL), 32-Bit (DADD, DSUB, DDIV, DMUL), Data Registers30 Mins
Arithmetic Instruction – Workout90 Mins
Comparison Instructions – 16-Bit & 32-Bit Comparison Instructions (LD<, LD>, LD=, LD<>, LD<=, LD>=)30 Mins
Comparison Instructions – Workout120 Mins
Move Instructions – 16-Bit (MOV, CML, BMOV, FMOV, XCH), 32-Bit (DMOV, DCML, DBMOV, DFMOV, DXCH)30 Mins
Move Instructions – Workout60 Mins
Program Control Part 1 – MC, MCR30 Mins
Program Control Part 2 – JMP, CALL, FEND, SRET, For, Next30 Mins
Program Control Part 3 – Working of Interrupts, IRET, EI, DI30 Mins
Program Control – Workout120 Mins
Analog & PID Control – FROM, TO, PID, PIDAT, SCL, AVG, MEAN, FILTER, CMP, ZCP, ADC, DAC, PWM, RAMP, DAVG, DSCL, PIDRUN, PIDSTOP60 Mins
Analog & PID Control – Workout90 Mins
Index Registers – Data Registers, KnX, KnY, KnM, E, F30 Mins
Program Uploading / Downloading – Communication: PC to PLC, PLC to PLC30 Mins

Module 4 – Omron PLC (CX-Programmer)

Introduction – Device Overview, Tool Installation, I/O Addressing Format & Range, Programming Rules30 Mins
Basic Elements Part 1 – Bit Function, Logic Gates, NO & NC, Coil30 Mins
Basic Instruction Part 1 – Workout150 Mins
Basic Instruction Part 2 – Latching & Unlatching, Internal Bit Function (Memory)30 Mins
Basic Instruction Part 2 – Workout120 Mins
Basic Instruction Part 3 – Rising/Falling Edge Trigger Switch, Set & Reset, DIFU & DIFD, KEEP30 Mins
Basic Instruction Part 3 – Workout120 Mins
Timer Instruction – Timer BCD/Binary, Totalising Timer, Timer/Counter Reset (BCD/Binary)30 Mins
Timer Instruction – Workout120 Mins
Counter Instruction – Counter BCD/Binary, Reversible Counter, Timer/Counter Reset30 Mins
Counter Instruction – Workout120 Mins
Arithmetic Instruction Part 1 – Signed Binary Add/Sub/Mul/Divide (Single & Double/Long)30 Mins
Arithmetic Instruction Part 2 – BCD Add/Sub/Mul/Divide (Single & Double/Long)30 Mins
Arithmetic Instruction – Workout120 Mins
Data Comparison – Less Than, Equal To, Greater Than, Compare, Area Range Compare (Standard & Long, Signed Variants)30 Mins
Data Comparison – Workout120 Mins
Sequence Control Part 1 – Interlock, Interlock Clear30 Mins
Sequence Control Part 2 – Conditional Jump, Jump End, Jump30 Mins
Sequence Control Part 3 – Subroutine Enter, Subroutine Define, Return30 Mins
Sequence Control – Workout120 Mins
Data Move Part 1 – Move, Move Not, Block Set, Transfer, Data Exchange30 Mins
Data Move Part 2 – Collect, Distribute30 Mins
Data Move – Workout120 Mins
Logic Operators – 16-Bit (AND, OR, XOR, Complement), 32-Bit (Double AND/OR/XOR, Complement Long)30 Mins
Logic Operators – Workout60 Mins
Analog & PID Control – SCL, SCL2, APR, AVG, XFER, BSET, PIDAT, FILTER, PID/PIDAT/PIDX, CMP/BCMP, LIMIT, PWM, SPED, PLS260 Mins
Analog & PID Control – Workout90 Mins
Program Uploading / Downloading – Communication: PC to PLC, PLC to PLC30 Mins

Module 5 – Mitsubishi PLC (GX-Works 3)

Introduction – Device Overview, Software Introduction & Installation30 Mins
Basic Instructions Part 1 – Input/Output Addressing (X0/Y0), NO, NC, Coil, Vertical & Horizontal Line30 Mins
Basic Instruction Part 1 – Workout: Ladder Diagram for Logic Gates & Reference Workout180 Mins
Basic Instruction Part 2 – Latching, Un-Latching, Memory Contact (M0)30 Mins
Basic Instruction Part 2 – Workout150 Mins
Basic Instruction Part 3 – Rising Edge, Falling Edge, Set, Reset30 Mins
Basic Instruction Part 3 – Workout120 Mins
Timer Instruction – Overview, Working, Types, Addressing of Timer30 Mins
Timer Instruction – Workout240 Mins
Counter Instruction – Overview, Working, Types, Addressing of Counter30 Mins
Counter Instruction – Workout120 Mins
Arithmetic Instruction – 16-Bit & 32-Bit Instructions, Data Registers30 Mins
Arithmetic Instruction – Workout90 Mins
Comparison Instructions – 16-Bit & 32-Bit Comparison Instructions30 Mins
Comparison Instructions – Workout120 Mins
Move Instructions – 16-Bit & 32-Bit Move Instructions30 Mins
Move Instructions – Workout60 Mins
Program Control Part 1 – MC, MCR30 Mins
Program Control Part 2 – JMP, CALL, FEND, SRET30 Mins
Program Control Part 3 – For, Next30 Mins
Program Control Part 4 – Working of Interrupts, IRET, EI, DI30 Mins
Program Control – Workout120 Mins
Index Registers – Data Registers, KnX, KnY, KnM, E, F30 Mins
Analog & PID Control – SCL, ZCP, LIMIT, AVG, WSFL, DECO, ENCO, PWM, PLSY, PLSR, ADRSET, A/D, D/A, RAMP, PID Family, AUTOTUNE60 Mins
Analog & PID Control – Workout90 Mins
Program Uploading / Downloading – Communication: PC to PLC, PLC to PLC30 Mins

Module 6 – Siemens PLC (TIA Portal)

Introduction – Specification of Siemens PLC, Device Overview, Software Introduction & Installation30 Mins
Basic Instructions Part 1 – Input/Output Addressing (X0/Y0), NO, NC, Coil, Vertical & Horizontal Line30 Mins
Basic Instruction Part 1 – Workout: Ladder Diagram for Logic Gates & Reference Workout180 Mins
Basic Instruction Part 2 – Latching, Un-Latching, Memory Contact30 Mins
Basic Instruction Part 2 – Workout150 Mins
Basic Instruction Part 3 – Rising Edge, Falling Edge, Set, Reset30 Mins
Basic Instruction Part 3 – Workout120 Mins
Timer Instruction – Overview, Working, Types, Addressing of Timer30 Mins
Timer Instruction – Workout240 Mins
Counter Instruction – Overview, Working, Types, Addressing of Counter30 Mins
Counter Instruction – Workout120 Mins
Arithmetic Instruction – 16-Bit & 32-Bit Instructions, Data Registers30 Mins
Arithmetic Instruction – Workout90 Mins
Comparison Instructions – 16-Bit & 32-Bit Comparison Instructions30 Mins
Comparison Instructions – Workout120 Mins
Move Instructions – 16-Bit & 32-Bit Move Instructions30 Mins
Move Instructions – Workout60 Mins
Program Control Part 1 – MC, MCR30 Mins
Program Control Part 2 – JMP, CALL, FEND, SRET30 Mins
Program Control Part 3 – For, Next30 Mins
Program Control Part 4 – Working of Interrupts, IRET, EI, DI30 Mins
Program Control – Workout120 Mins
Registers – Data Registers in TIA Portal30 Mins
Program Uploading / Downloading – Communication: PC to PLC, PLC to PLC30 Mins
Analog & PID Control – NORM_X, SCALE_X, SCALE, UNSCALE, LIMIT, TRUNC, ROUND, CEIL, FLOOR, PID_Compact/Temp/3Step, FILTER, RAMP, PWM, AI/AO_SCALE, CONT_C, FB Family, PID_CTRL/SELF_TUNE/AUTOTUNE, TCONT_CP/S, PULSEGEN60 Mins
Analog & PID Control – Workout90 Mins

Module 7 – HMI (Human Machine Interface) – Delta HMI

Introduction to HMI – HMI & Industrial Automation, Delta DOP Series Overview, DOP-107WV Features, Hardware Connections & Power Supply, Communication Basics, DIA Studio Installation60 Mins
DIA Studio Interface & Project Setup – Workspace Overview, Project Explorer & Screen Management, System & Communication Settings, PLC Model & Tag Addressing, Upload/Download & Simulation60 Mins
Basic Elements Part 1 – Button Elements, Indicator Elements30 Mins
Basic Elements Part 2 – Analog Element, Meter Element, Bar Element30 Mins
Basic Elements Part 3 – Input Element, Keypad Element, Data Display Element30 Mins
Basic Element Part 4 – List Element, Curve Element, Basic Shape Element, Drawing Element60 Mins
Basic Elements – Workout120 Mins
PLC Communication & Addressing – PLC-HMI Communication Concepts, Delta PLC Memory Areas, X/Y/M/D/T/C Addressing, Internal HMI Registers, Error Handling, COM Port & Ethernet60 Mins
PLC Communication & Addressing – Workout: Read PLC I/O, Control PLC Bits, Display PLC Data120 Mins
Data Management Part 1 – Alarm History Table, Active Alarm List, Alarm Frequency Table, Alarm Moving Sign, Alarm Settings60 Mins
Data Management Part 2 – 16-Bit Recipe, 32-Bit Recipe, Enhanced Recipe, Encode Tool, Recipe Viewer60 Mins
Data Management Part 3 – Historical Trend Graph, Historical Data/Event/Overview Table, Circular Trend, History Buffer60 Mins
Data Management – Workout120 Mins
Macro Part 1 – Screen Open/Close/Cycle Macro, Screen Cycle Macro Manager30 Mins
Macro Part 2 – Submacro, Initial Macro, Background Macro, Clock Macro60 Mins
Macro – Workout120 Mins
Upload and Download Program – HMI to PC, PC to HMI30 Mins
Project – Any Project with HMI and PLC90 Mins

Module 8 – SCADA (Supervisory Control and Data Acquisition) – InTouch

Introduction to SCADA – What Is SCADA, PLC vs HMI vs SCADA, SCADA Architecture, InTouch Overview & Features, Industrial Applications, Real-Time Monitoring Basics30 Mins
InTouch Development Environment – Installing InTouch, WindowMaker & WindowViewer, Creating New Application, Application Manager, Menus & Toolbars, File Management, Backup & Restore30 Mins
Windows and Navigation – Window Types (Replace, Overlay, Popup), Creating Windows, Window Properties & Scripts, Multi-Window Navigation, Screen Resolution, Template & Startup Windows60 Mins
Tags and Databases – What Is a Tag, Creating/Modifying Tags, System/Memory/I-O/Indirect/Message Tags, Naming Standards, Data Types, Scaling, Import/Export, Alarm & Historical Tags30 Mins
Tags and Databases – Workout120 Mins
Script and Logic Part 1 – Introduction to InTouch Scripting (QuickScript), Windows Script60 Mins
Script and Logic Part 1 – Workout120 Mins
Script and Logic Part 2 – Event Scripts, Key Scripts, Application Scripts60 Mins
Script and Logic Part 2 – Workout120 Mins
Objects and Graphics – Symbol Factory, Drawing Tools, Standard Objects, Bitmap Images, Grouping & Layering60 Mins
Animation Part 1 – Discrete, Analog, Color, Visibility, Position, Size Animation30 Mins
Animation Part 1 – Workout60 Mins
Animation Part 2 – Rotation, Fill, Touch, Hyperlink Animation, Animation Wizards30 Mins
Animation Part 2 – Workout60 Mins
Alarms and Events – Alarm Groups, Setup & Configuration, Alarm Display, Alarm Commands60 Mins
Alarms and Events – Workout120 Mins
Recipe Management Part 1 – Introduction to Recipes, Types, Components, Creation, Loading & Downloading30 Mins
Recipe Management Part 2 – Recipe Security, Storage, Switching, Integration, Alarm Handling in Recipes30 Mins
Recipe Management – Workout: Motor Speed, Temperature Control, Tank Mixing, Batch Production Recipe120 Mins
Dynamic Data Exchange – What Is DDE, Purpose of DDE, Real-Time Data Sharing30 Mins
Dynamic Data Exchange – Workout120 Mins
Trends and Graphs – Real-Time & Historical Trending, Trend Controls, Trend Group Configuration, Data Logging (Historian)60 Mins
Trends and Graphs – Workout60 Mins
Reports – Report Setup, Generating & Viewing Reports, Report Distribution30 Mins
Security – Users and Privileges, Security Levels, Best Practices60 Mins
Testing, Running and Deployment – Application Testing (WindowViewer), Running Application (Runtime), Making Executable (.exe), Deployment Best Practices60 Mins
Project150 Mins