Certified in PLC Course — Pumo Technovation

Certified in PLC

Total Number of Modules6

Total Number of Topics112

Estimated Duration132:00 H

Module 1 – Introduction of Automation

Introduction of Automation – What Is Automation, Revolution of Industrial Automation, Basic Electrical & Circuit Breaker, Types of Relay & Contactor60 Mins

Module 2 – Control Panel Wiring

Relay - Circuit Design – Relay Circuit Design for Logic Gates: AND Gate, OR Gate30 Mins
Relay - Circuit Design Practice – Design Relay Circuit for NAND, NOR, Ex-OR, Ex-NOR Gates60 Mins
Relay - Basic Workout – 5 Basic NO, NC Concepts from PLC120 Mins
Control Panel - Circuit Design – Types of Panel Wiring in PLC, Designing Panel Wiring for Delta PLC (Sink Input Source Output)60 Mins
Control Panel - Circuit Design Practice – PLC Control Panel Wiring: Sink-Sink, Source-Sink, Source-Source90 Mins
Control Panel - Circuit Wiring – Delta PLC Wiring (Sink Input Source Output), Power Supply, Input & Output Module for PLC300 Mins

Module 3 – Delta PLC (WPLSoft)

Introduction – Specification of Delta PLC, Device Overview, Software Introduction & Installation30 Mins
Basic Instructions Part 1 – Input Addressing (X0), Output Addressing (Y0), NO, NC, Coil, Vertical & Horizontal Line30 Mins
Basic Instruction Part 1 – Workout: Ladder Diagram for Logic Gates & Reference Workout240 Mins
Basic Instruction Part 2 – Latching, Un-Latching, Memory Contact (M0)30 Mins
Basic Instruction Part 2 – Workout180 Mins
Basic Instruction Part 3 – Rising Edge, Falling Edge, Set, Reset30 Mins
Basic Instruction Part 3 – Workout120 Mins
Timer Instruction – Overview, Working, Types, Addressing of Timer30 Mins
Timer Instruction – Workout180 Mins
Counter Instruction – Overview, Working, Types, Addressing of Counter30 Mins
Counter Instruction – Workout120 Mins
Arithmetic Instruction – 16-Bit (ADD, SUB, DIV, MUL), 32-Bit (DADD, DSUB, DDIV, DMUL), Data Registers30 Mins
Arithmetic Instruction – Workout90 Mins
Comparison Instructions – 16-Bit & 32-Bit Comparison Instructions (LD<, LD>, LD=, LD<>, LD<=, LD>=)30 Mins
Comparison Instructions – Workout120 Mins
Move Instructions – 16-Bit (MOV, CML, BMOV, FMOV, XCH), 32-Bit (DMOV, DCML, DBMOV, DFMOV, DXCH)30 Mins
Move Instructions – Workout60 Mins
Program Control Part 1 – MC, MCR30 Mins
Program Control Part 2 – JMP, CALL, FEND, SRET, For, Next30 Mins
Program Control Part 3 – Working of Interrupts, IRET, EI, DI30 Mins
Program Control – Workout120 Mins
Analog & PID Control – FROM, TO, PID, PIDAT, SCL, AVG, MEAN, FILTER, CMP, ZCP, ADC, DAC, PWM, RAMP, DAVG, DSCL, PIDRUN, PIDSTOP60 Mins
Analog & PID Control – Workout90 Mins
Index Registers – Data Registers, KnX, KnY, KnM, E, F30 Mins
Program Uploading / Downloading – Communication: PC to PLC, PLC to PLC30 Mins

Module 4 – Omron PLC (CX-Programmer)

Introduction – Device Overview, Tool Installation, I/O Addressing Format & Range, Programming Rules30 Mins
Basic Elements Part 1 – Bit Function, Logic Gates, NO & NC, Coil30 Mins
Basic Instruction Part 1 – Workout150 Mins
Basic Instruction Part 2 – Latching & Unlatching, Internal Bit Function (Memory)30 Mins
Basic Instruction Part 2 – Workout120 Mins
Basic Instruction Part 3 – Rising/Falling Edge Trigger Switch, Set & Reset, DIFU & DIFD, KEEP30 Mins
Basic Instruction Part 3 – Workout120 Mins
Timer Instruction – Timer BCD/Binary, Totalising Timer, Timer/Counter Reset (BCD/Binary)30 Mins
Timer Instruction – Workout120 Mins
Counter Instruction – Counter BCD/Binary, Reversible Counter, Timer/Counter Reset30 Mins
Counter Instruction – Workout120 Mins
Arithmetic Instruction Part 1 – Signed Binary Add/Sub/Mul/Divide (Single & Double/Long)30 Mins
Arithmetic Instruction Part 2 – BCD Add/Sub/Mul/Divide (Single & Double/Long)30 Mins
Arithmetic Instruction – Workout120 Mins
Data Comparison – Less Than, Equal To, Greater Than, Compare, Area Range Compare (Standard & Long, Signed Variants)30 Mins
Data Comparison – Workout120 Mins
Sequence Control Part 1 – Interlock, Interlock Clear30 Mins
Sequence Control Part 2 – Conditional Jump, Jump End, Jump30 Mins
Sequence Control Part 3 – Subroutine Enter, Subroutine Define, Return30 Mins
Sequence Control – Workout120 Mins
Data Move Part 1 – Move, Move Not, Block Set, Transfer, Data Exchange30 Mins
Data Move Part 2 – Collect, Distribute30 Mins
Data Move – Workout120 Mins
Logic Operators – 16-Bit (AND, OR, XOR, Complement), 32-Bit (Double AND/OR/XOR, Complement Long)30 Mins
Logic Operators – Workout60 Mins
Analog & PID Control – SCL, SCL2, APR, AVG, XFER, BSET, PIDAT, FILTER, PID/PIDAT/PIDX, CMP/BCMP, LIMIT, PWM, SPED, PLS260 Mins
Analog & PID Control – Workout90 Mins
Program Uploading / Downloading – Communication: PC to PLC, PLC to PLC30 Mins

Module 5 – Mitsubishi PLC (GX-Works 3)

Introduction – Device Overview, Software Introduction & Installation30 Mins
Basic Instructions Part 1 – Input/Output Addressing (X0/Y0), NO, NC, Coil, Vertical & Horizontal Line30 Mins
Basic Instruction Part 1 – Workout: Ladder Diagram for Logic Gates & Reference Workout180 Mins
Basic Instruction Part 2 – Latching, Un-Latching, Memory Contact (M0)30 Mins
Basic Instruction Part 2 – Workout150 Mins
Basic Instruction Part 3 – Rising Edge, Falling Edge, Set, Reset30 Mins
Basic Instruction Part 3 – Workout120 Mins
Timer Instruction – Overview, Working, Types, Addressing of Timer30 Mins
Timer Instruction – Workout240 Mins
Counter Instruction – Overview, Working, Types, Addressing of Counter30 Mins
Counter Instruction – Workout120 Mins
Arithmetic Instruction – 16-Bit & 32-Bit Instructions, Data Registers30 Mins
Arithmetic Instruction – Workout90 Mins
Comparison Instructions – 16-Bit & 32-Bit Comparison Instructions30 Mins
Comparison Instructions – Workout120 Mins
Move Instructions – 16-Bit & 32-Bit Move Instructions30 Mins
Move Instructions – Workout60 Mins
Program Control Part 1 – MC, MCR30 Mins
Program Control Part 2 – JMP, CALL, FEND, SRET30 Mins
Program Control Part 3 – For, Next30 Mins
Program Control Part 4 – Working of Interrupts, IRET, EI, DI30 Mins
Program Control – Workout120 Mins
Index Registers – Data Registers, KnX, KnY, KnM, E, F30 Mins
Analog & PID Control – SCL, ZCP, LIMIT, AVG, WSFL, DECO, ENCO, PWM, PLSY, PLSR, ADRSET, A/D, D/A, RAMP, PID Family, AUTOTUNE60 Mins
Analog & PID Control – Workout90 Mins
Program Uploading / Downloading – Communication: PC to PLC, PLC to PLC30 Mins

Module 6 – Siemens PLC (TIA Portal)

Introduction – Specification of Siemens PLC, Device Overview, Software Introduction & Installation30 Mins
Basic Instructions Part 1 – Input/Output Addressing (X0/Y0), NO, NC, Coil, Vertical & Horizontal Line30 Mins
Basic Instruction Part 1 – Workout: Ladder Diagram for Logic Gates & Reference Workout180 Mins
Basic Instruction Part 2 – Latching, Un-Latching, Memory Contact30 Mins
Basic Instruction Part 2 – Workout150 Mins
Basic Instruction Part 3 – Rising Edge, Falling Edge, Set, Reset30 Mins
Basic Instruction Part 3 – Workout120 Mins
Timer Instruction – Overview, Working, Types, Addressing of Timer30 Mins
Timer Instruction – Workout240 Mins
Counter Instruction – Overview, Working, Types, Addressing of Counter30 Mins
Counter Instruction – Workout120 Mins
Arithmetic Instruction – 16-Bit & 32-Bit Instructions, Data Registers30 Mins
Arithmetic Instruction – Workout90 Mins
Comparison Instructions – 16-Bit & 32-Bit Comparison Instructions30 Mins
Comparison Instructions – Workout120 Mins
Move Instructions – 16-Bit & 32-Bit Move Instructions30 Mins
Move Instructions – Workout60 Mins
Program Control Part 1 – MC, MCR30 Mins
Program Control Part 2 – JMP, CALL, FEND, SRET30 Mins
Program Control Part 3 – For, Next30 Mins
Program Control Part 4 – Working of Interrupts, IRET, EI, DI30 Mins
Program Control – Workout120 Mins
Registers – Data Registers in TIA Portal30 Mins
Program Uploading / Downloading – Communication: PC to PLC, PLC to PLC30 Mins
Analog & PID Control – NORM_X, SCALE_X, SCALE, UNSCALE, LIMIT, TRUNC, ROUND, CEIL, FLOOR, PID_Compact/Temp/3Step, FILTER, RAMP, PWM, AI/AO_SCALE, CONT_C, FB Family, PID_CTRL/SELF_TUNE/AUTOTUNE, TCONT_CP/S, PULSEGEN60 Mins
Analog & PID Control – Workout90 Mins